drops with pull ring direct-manufacture,factory,supplier from China

The pull ring plug of drip irrigation tape is a fitting used with drip irrigation tape. It is used for the end sealing of drip irrigation tape, which plays a role of flow closure.Specification and model: 16mm, PE materialUsage:Cut the end of drip irrigation tape with scissors and insert it between the blue pull ring and black part of the pipe fitting.Pull the blue pull ring outward and clamp the drip irrigation tape tightly.

The pull ring straight through is used for the connection between drip irrigation tape and drip irrigation tape. Through the reasonable use of pull ring straight through, some shorter drip irrigation tapes can be reused, saving materials and reducing the project cost.Instructions: when in use, insert the pull ring straight through into the drip irrigation tape, and then use the pull ring to lock the drip irrigation tape. The operation method on the other side is the same.

Instructions for use: Mainly used for capillary head end control (the right end of the pull ring is connected to a 16mm drip tape, which is fixed by the pull ring; the left end is connected to the water delivery main pipe, which can be used for PE pipes (wall thickness greater than 1mm), water delivery tape or use with matching rubber bands , Connect with pvc pipe.)Product introduction: The pull-ring bypass switch is a commonly used drip irrigation switch.

The drip irrigation belt snap tee has the following advantages: 　　1. There are internal parts such as locking hoop, stepped ring seal ring, etc. The nuts on both sides can be disassembled for assembly and use, which improves the product reuse rate. And the product design is scientific and reasonable, the pipe fittings have high strength, good sealing performance, and no water leakage. 　　2. The drip irrigation belt positive female snap tee is easy to install and use, easy to disassemble, flexible, easy to recycle, beautiful and practical.

Product introduction: the pull ring bypass switch is a common drip irrigation switch, one end of which is connected with the main water tape or PE pipe, and the other end is connected with the drip irrigation tape, so as to achieve the effect of controlling the water flow in the rear section of the valve.Instructions for use: it is mainly used for controlling the head end of the capillary (the right end of the pull ring is connected with a 16mm drip irrigation tape, which is fixed by the pull ring; The left end is connected with main water delivery pipe, which can be used for PE pipe (wal

Product features: scientific design, high strength, good sealing, convenient connection, easy disassembly, strong flexibility, easy recycling, and beautiful appearance. It is made of engineering plastics and has a long service life.

Instructions for use: used for the connection and front-end control of the water delivery belt and the drip irrigation belt (one end of the valve is connected to a 16mm drip irrigation belt, which is fixed by a screw lock; the other end is connected to the main water delivery belt)How to use: First use a hole punch (14mm in diameter) to punch holes on the side of the soft water belt, then rotate the bypass valve of the drip irrigation belt into the hole of the soft belt, tighten the nut to fix the bypass on the soft water belt, and on the other side Just connect the drip tape.

Purpose: the drip irrigation system uses the product when the tape is the main pipe. Branch water source, the main pipeline (soft tape) is connected with drip irrigation tape, so that the water in the main pipeline (soft tape) flows into the drip irrigation tape respectively.Usage: use a puncher (14mm in diameter) to make a hole on the side of the soft water tape, and then rotate the three-way into the soft tape hole, tighten the nut to fix the bypass on the soft water tape, and connect the drip irrigation tape on the other sideParameters:Model:16mmMaterial: PE plastic

Precise filtration: Filter discs with different precisions can be selected according to the water requirements. There are 20 microns, 55 microns, 100 microns, 130 microns, 200 microns, 400 microns and other specifications, and the filtration ratio is greater than 85%.Thorough and efficient backwashing: Because the filter pores are completely opened during backwashing, and the centrifugal jet effect is added, the cleaning effect that other filters cannot achieve can be achieved.

Principle: when the water flows through the conical tank, it will rotate and generate centrifugal force, so that the sediment and solid particles with higher density in the water resources will enter the sand settling tank, and the clear water enters the Y-shaped net filter from S-bend (C-bend) for secondary filtrationPrecautions:1. The centrifugal filter sand tank is equipped with a sand discharge port.

Precise filtration: Filter discs with different precisions can be selected according to the water requirements. There are 20 microns, 55 microns, 100 microns, 130 microns, 200 microns, 400 microns and other specifications, and the filtration ratio is greater than 85%.Thorough and efficient backwashing: Because the filter pores are completely opened during backwashing, and the centrifugal jet effect is added, the cleaning effect that other filters cannot achieve can be achieved.

16mm double lock-nut bypass valve and double thread bypass switch are made of high-quality engineering plastics. The products are of high quality and durable. This kind of drip irrigation bypass switch adopts double thread form with tight connection, good water locking effect and no water leakage.Installation steps: drill 8 mm hole in the main water supply pipe, insert the bypass valve, rotate the lock-nut, and connect the 16mm end with the drip irrigation tape. Tip: after drilling holes on PE pipe and plastic hose, directly insert and install it.

Performance characteristics:The sprinkler is completely imported from Israeli technology and adopts a vortex nozzle design to provide vortex spray flow and minimize the possibility of cloggingThe atomization effect is good. With the help of the anti-dripping device, the phenomenon of dripping and damage to the seedlings after spraying can be effectively avoidedDetachable structure, easy to maintain.

Precise filtration: Filter discs with different precisions can be selected according to the water requirements. There are 20 microns, 55 microns, 100 microns, 130 microns, 200 microns, 400 microns and other specifications, and the filtration ratio is greater than 85%.Thorough and efficient backwashing: Because the filter pores are completely opened during backwashing, and the centrifugal jet effect is added, the cleaning effect that other filters cannot achieve can be achieved.

Drip irrigation dripper characteristics1. Silicone sheet inside the dripper can change the section of the water outlet, realize the effect of stable water flow and flow regulation. It can be installed on fruit trees, saplings and forest trees with a relatively long distance, and the distance between the drippers can be adjusted arbitrarily according to the distance between crops. Suitable for various terrains such as plains, mountains, plateaus, terraces, hills, etc.2. The dripper has a small volume, so it is easy to install.

Suitable occasions: suitable for various terrain and crops, especially in irrigation area with large slope fluctuation; Suitable for the case where the laying length of drip irrigation pipe is large; Suitable for the emitter spacing changes; When the system pressure is unstable.

Drip irrigation : The inlaid drip irrigation pipe is an integrated drip irrigation pipe with a cylindrical dripper embedded on the inner wall of the pipe. The dripper is assembled on the inner wall of the pipe while producing the pipe, which is easy to install and use.Classification1. According to the water outlet method, it is divided into:Pressure Compensated Drip Irrigation Pipes and Non-Pressure Compensated Drip Irrigation Pipes2. According to the structure can be divided into:In-line drip irrigation pipe and inter-pipe drip irrigation pipeapplicationApplicable conditions:1.

Purpose: it is usually used in drip irrigation system, when PE soft tape is used as main (branch) pipe, and the soft tape three-way is used as water separation device to connect with drip irrigation tape. That is, the irrigation system uses soft tape as low-pressure water transmission pipeline, and uses soft tape three-way to connect with soft tape , and then connects with drip irrigation tape through the reversed lock-nut on the soft tape three-way, and supplies water to drip irrigation tape of both sides, thus forming rapid and accurate irrigation of water source.

The product has many types, with the characteristics of quick and convenient connection and disassembly, good sealing performance, high strength and long service life. It is widely used in field micro -spray irrigation project.

Installation and usage: the product is used in the project of PE small pipe or drip irrigation pipe. Compared with the traditional PE socket straight through and bypass, the advantages are that the user can adjust the switch of each irrigation pipe tape and increase the controllability of the system.through is made of new engineering plastics, with beautiful appearance, strong anti-aging performance, low cost and long service life. Scientific design, convenient connection, easy disassembly, strong flexibility, good sealing, beautiful and practical, and easy to install and use, easy to recycle.

The composition of ground-inserting micro-sprinkler, inserting rod, capillary, capillary double joint and epsilon-type adapter.Micro-sprinkler: the ground-inserting micro-sprinkler generally adopts the ground-inserting refraction atomization micro-sprinkler or the ground-inserting double-sided wheel micro-sprinkler with better atomization effect, so as to provide better atomization effect or larger spraying radius and meet different needsInserting rod: it is inserted into the ground for fixing, as a support for the ground-inserting micro-sprinkler.

principle:When the filter is working normally, the pressurized water flows into the tank from the water inlet and reaches the filter layer evenly. When the water flows through the filter layer, the impurities are filtered and retained. There is a water trap with a valve at the bottom of the filter, and the filtered water is collected evenly and then flows out of the filtering equipment.With the continuous accumulation of impurities in the filter layer, the water flow loss continues to increase.

The pressure compensation drip irrigation pipe is made of high-density PE pipe with improved nanotechnology and built-in pressure compensation emitter. It is suitable for complex terrain and has the characteristics of good uniformity, strong anti-clogging ability and long service life.The commonly used model of pressure compensation drip irrigation pipe is Φ16. The distance between the emitters is 300mm (200), the wall thickness is 0.6mm, 0.8mm and 1.0mm.

Product features:It is made of new engineering plastics, with aging-resistant process and materials, long service life, mainly supporting export products.Scientific design, high strength, good sealing, convenient connection, easy disassembly, strong flexibility, easy recycling, beautiful appearance.It is mainly applicable to the irrigation of vegetables, fruit trees, shrubs, nurseries and other ground crops, and can be used for tree crown cooling and tree frost preventionSpraying and drip irrigation of plant cooling, urban environmental protection, lawn and other aspects.Instruc